Power

輸入電源

· Power rated: 12KW (208-240V)

· 額定功率：12KW (208-240V)

Voltage

電壓

· Voltage rated:  AC208-240V 50/60HZ

· 額定電壓： AC208-240V 50/60HZ

Working Temperature

工作溫度

· Max. Temperature: 1100 °C ( 1 hr)

   最高溫度：1100℃ (1小時)

· Continuous working temperature: ≤1000℃

   持續工作溫度：≤1000℃

· Recommended heating Rate: ≤10°C /min

   推薦升溫速率：≤10℃/分鐘

Temperature Controller

控溫方式

· PID automatic control and auto-tune function.

   模糊PID控制和自整定調節

· 30 programmable segments for precise thermal processing.

   智能化30段可編程控制

· Built-in protection for the over-heated and broken thermocouple. 

超溫和斷偶報警功能

Length of heating zone

加熱區長度

· 300+300+300mm

Length of constant zone

恒溫區長度

· 150+200+150mm

Heating Elements

加熱元件

· Resistance wire, Fe-Cr-Al Alloy doped by Mo

· 電阻絲（摻鉬鐵鉻鋁合金）

Temperature Accuracy

控溫精度

+/- 1 °C

Dimensions

尺寸

· Tube size: Φ150/210/280*1300mm (optional)

· 爐管尺寸：Φ150/210/280*1300mm (可選)

· Overall size: 1300*650*1000mm

· 外形尺寸：1300*650*1000mm

· Two fibrous ceramic tube blocks are included for blocking heat radiation generated from tube center. (Ceramic blocks must be fully inserted into the furnace chamber before heating).

· 兩個氧化鋁管堵阻擋管中心產生的熱輻射（氧化鋁管堵必須在加熱前塞進爐膛）

Vacuum Flange

真空法蘭
 

· One end is KF25 quick clamp flange

   一端為KF25快速卡箍法蘭

· Another end is screw tighten flange with gas inlet

   另一端為進氣螺絲緊固法蘭

Vacuum Pressure

真空壓力

· 10^-1pa can be achieved by mechanical pump

   機械泵可達10^-1pa

· 10^-3pa can be reached by molecular pump

   分子泵可達10^-3pa

Net Weight

凈重

250kg

Warranty

質保

One year limited warranty with lifetime support  (Such consumable parts as tube, quartz block, and O-rings, etc. are NOT supported by the warranty)

一年質保終身支持（消耗品如爐管，石英管堵，O型圈等不在質保范圍內）

Warning

注意事項

· Toxic or explosive gasses are not recommended for use with this furnace without necessary safety controls and supervision. Please put furnace into fume hood for better safety

· 沒有安全控制和監督的情況下，不建議使用有毒或爆炸性氣體。為了安全，請把爐子放在通風處。

· Small cracks may appear on the surface of the refractory ceramics over extended use. This is a normal occurrence and the cracks may be repaired with alumina coating.

· 在使用過程中爐膛表面可能出現細小裂紋。這是正常情況，裂紋可以用氧化鋁涂層修復。

Compliance

認證

· CE Certified

   CE認證