南澳電氣NABZ全自動變比組別測試儀采用了大屏幕中英文液晶屏顯示、內置中英文菜單式操作，完成一組變壓器的測試只需11秒。NABZ全自動變比組別測試儀是電力工業部門的理想測試儀器。

 南澳電氣（武漢）有限公司（簡稱“南澳電氣”)，是國電網武漢高壓研究所改制后成立的高電壓輸變電檢測設備的高新骨干企業，主要從事電力儀器儀表、交直流分壓器、互感器類測試設備、高壓耐壓設備、峰值電壓表、超聲局放定位系統、工頻信號發生器、沖擊電壓電流發生器 、變壓器類試驗設備、繼電保護測試儀、SF6及開關類檢測設備、局部放電超聲檢測系統、避雷器測試設備、環境人工氣候模擬實驗裝置、電能表校驗設備、蓄電池檢測儀等產品的研發。

NABZ Automatic Variable Ratio Group Tester    南澳電氣NABZ全自動變比組別測試儀

產品簡介

南澳電氣NABZ全自動變比組別測試儀的變比，操作過程繁瑣、測量范圍狹窄，已經不適應現代測量快節奏、率的要求。為此，南澳電氣（武漢）有限公司采用現代電子技術，研制出了新一代全自動變比組別測試儀。它體積小，重量輕，精度高，穩定性好。南澳電氣NABZ全自動變比組別測試儀采用了大屏幕中英文液晶屏顯示、內置中英文菜單式操作，完成一組變壓器的測試只需11秒。NABZ全自動變比組別測試儀是電力工業部門的理想測試儀器。

南澳電氣NABZ全自動變比組別測試儀產品別名

變壓器變比組別測試儀，變壓器雙臂電橋

南澳電氣NABZ全自動變比組別測試儀產品特性

1．自動測量接線組別。

2．自動進行組別變換。

3．自動切換相序。

4．自動切換量程。

5．自動校表。

6．輸入標準變比后，能自動計算出相對誤差。

7. 一次測量完成，自動切斷試驗電壓 。

8. 設置數據,測量結果自動保存，可查看以前數據。

9. 測量有載變壓器,只輸入一次變比。

南澳電氣NABZ全自動變比組別測試儀產品參數

1．變比測量范圍： 1—10000

2．組別：1—12點

3．精度: 1-1000 0.2 級 1000-10000 0.5級

4．電源：AC220V ±10%，50HZ

5．使用環境溫度：-5℃ ─ 40℃

6．使用環境濕度：＜85%

7．體積：430mm×320mm×215mm

8．重量：8Kg

 

南澳電氣NABZ全自動變比組別測試儀注意事項

1. 保險1為2A,保險2為0.。如果測試線短路,高低壓接反,會熔斷保險。保險熔斷后，如果進行測量，在顯示“ 正在測量，請等待！ ”后停住。請關機，更換相同容量的保險，重測。

2.連線要保持接觸良好。儀器應良好接地！

3.儀器的工作場所應遠離強電場、強磁場、高頻設備。供電電源干擾越小越好，宜選用照明線,如果電源干擾還是較大，可以由交流凈化電源給儀器供電。交流凈化電源的容量大于200VA即可。

4.儀器工作時，如果出現液晶屏顯示紊亂，按所有按鍵均無響應，或者測量值與實際值相差很遠，請按復位鍵,或者關掉電源,再重新操作。

5.顯示器沒有字符顯示,或顏色很淡,請調節亮度電位器至合適位置。

亮度電位器是多圈電位器 ，有10圈！

6.儀器應存放在干燥通風處，如果長期不用或環境潮濕，使用前應加長預熱時間，去除潮氣。

7.通訊口調試時使用。

 

Product introduction

When using this radio bridge to measure the transformer ratio, the operation procedure is complex, the measuring measure range is narrow, which is no longer meet modern fast-paced, high-efficiency requirements. Therefore, NABZ electrical uses the modern electronic technology, developed a new generation of automatic variable ratio group tester. It is small, light, high accuracy and with good stability. It uses a large-screen character display, menu operation, friendly interface. The variable group can measure at once. NABZ Automatic variable ratio group tester is ideal product for electrical industry department.

Also called name

Transformer ratio group tester, transformer ratio tester, transformer ratio automatic tester, automatic transformer ratio tester, transformer ratio group testing device, transformer ratio testing device, transformer ratio automatic testing device.

The Characteristics of the products

1. Automatic measurement wiring group.

2. Automatic group transformation.

3. Automatic switching phase sequence.

4. Automatic shift ranging.

5. Automatic calibration.

6. Input the standard ratio, it can automatically calculate the relative error.

7.When the measurement is completed, it can cut off the testing voltage automatically .

8. Setting the data, the measured results can be saved automatically, and can be view the previous data.

9. Measuring loaded transformer ratio, only need to enter once

The parameters of the products

1. Ratio measuring range: 1-10000

2. Group:1-12:00

3. Accuracy: 1-1000  0.2 grade,1000-10000 0.5 grade

4. Power supply: AC220V ± 10%, 50HZ

5. Operating temperature: -5 ℃ ─ 40 ℃

6. Operating humidity: <85%

7. Volume: 430mm × 320mm × 215mm

8. Weight: 8Kg

 

Power supply: AC110V/115V/120V/127V/220V/230V/240V optional

Input frequency: 50Hz/60Hz optional

Note: The users can select the corresponding power which based on their local supply voltage and frequency, and we will confirm it before the delivery (or inform us that the goods will be used in which country advance)

 

Attentions should take

1.Insurance 1 is 2A, Insurance 2 is 0.. If the testing line is short-circuit , the high and low voltage will be reversed, will burn the fuse. once fused, it will be displayed " measuring , wait ! " and then stop to operate and cut off the power.Please replace the same capacity insurance, then retesting .

2.Maintain the connections is fine. The instrument should be well grounded !

3.Ensure the workplace keep away from strong electric field , magnetic field and high-frequency devices. Power supply interference should be the smaller the better, and use light line. If the power supply interference is still large, it better to use the AC purified power,.the purified AC power supply capacity just larger than 200VA will do.

4.During the operating, if there is disorder on LCD screen, and without any response after press all the button, or the measured value is much very far away from the actual value, please press the reset button, or turn off the power, then restart the operate .

5.If the displays without character display ,or the color is weak, please adjust the brightness potentiometer to the appropriate location . Brightness potentiometer is a multi-turn potentiometer with 10 laps !

6.The instrument should be stored in dry and ventilated place , if unused for a  long-term, or stored in a humid environment, it need to extend the warm-up time before using , to remove  the moisture.

7.Communication port used for debugging .

本頁產品地址：http://jssdj.com/sell/show-7247736.html